Wireless Fire Alarm Control Panel WCP1
Mua ngay Gọi điện xác nhận và giao hàng tận nơiDescription
INTRODUCTION
- The WCP-1 is a wireless fire alarm control panel with up to 160 addressable devices.
- It uses a mesh network on 444.4 MHz radio, so no signal cable is needed.
- Each detector runs on one 3V battery for over 36 months.
The FireSmart wireless fire alarm system is the most popular choice in Vietnam. Under local fire codes, every building except a private house needs a fire alarm system. Villas, small hotels and restaurants therefore often choose the wireless option.
Historical and religious buildings also need it, because signal cables cannot be run inside. The system suits any place where wiring detectors is impossible or undesirable.
The system forms a MESH-NETWORK. Each wireless device talks to its neighbours, so at least two redundant paths are always available. This gives the reliability of a cable-based solution.
Signals travel by radio, with no signal cables. This saves labour and installation time. We do not cut ceilings or walls for cable routing, so the structure and look of the house stay intact.
System configuration
The control panel connects to 160 programmable addressable fire alarm devices. Two onboard output relays control external devices in case of fire.
The link between the panel and the wireless smoke and heat detectors is designed to meet TCVN 7568-14:2025 (based on ISO 7240). The devices also meet common international rules for radio use.
All wireless smoke and heat detectors, manual call points and modules are addressable. You can name each device on a PC, in the mobile app, or on the panel itself.
Each detector runs on an ordinary 3V battery, easy to buy at any store. One battery lasts over 36 months. When capacity drops below 20%, the device warns you with LED lights and repeated sounds two months before the battery runs out.
The warranty is valid for 24 months after first use. Installations in several countries show the system works well even in hard conditions.
Emergency alerts go to the horn and lamp, and also to your phone by SMS, voice call and app notification. You stay informed even when you are away from home.
Remote monitoring: panel, FCOM and the FireSmart app
The WCP-1 raises the alarm on site. Two more FireSmart products send the alarm and the system status to people who are not in the building.
| Layer | What it does |
|---|---|
| WCP-1 panel | Shows alarms and faults on its 4-line LCD. You can name each device on the panel, on a PC or in the mobile app. Panels can be networked, up to 64. |
| FCOM transmission device | FCOM-1 connects to the NO/NC output of a fire alarm panel. It makes up to 20 simultaneous alarm calls from a phone book of 100 numbers. It uses an optional 4G SIM or WiFi, and has a 24-hour backup battery. |
| FireSmart management software (FAMS) | Mobile app (Android and iOS) and PC software share one account and one set of data. They show alarms and faults in real time, and warn by voice call and push notification. You can manage several panels and sites, and see low-battery warnings. |
Install the FCOM where the 4G or WiFi signal is stable. Together, the three layers let one team watch many sites from one place.
Technical specifications
- Fully compliant with and tested to ISO 7240 / TCVN 7568-14:2025-2, ISO 7240 / TCVN 7568-14:2025-4 and ISO 7240 / TCVN 7568-14:2025-25.
- Compatible with a wide range of wireless detection devices.
- Adjustable sounder delay time.
- Two monitor outputs (expandable to 16).
- Connects up to 160 addressable wireless devices.
- Fully programmable using a simple menu.
- Programmable using the mobile app.
- Analog design using FireSmart’s advanced protocol for fast and robust communication.
- 4 lines x 20 characters LCD display.
- Network capability of up to 64 panels.
- Auto learn feature.
| Parameter | Value |
|---|---|
| Supply voltage | 120VAC (50Hz/60Hz) or 220VAC (50Hz/60Hz) |
| Power supply DC rating | 24V 1.3 Amps |
| Main supply fuse | 1.3 Amp 250V |
| Dimension | 240mm(W) x 300mm(H) x 75mm(D) |
| Weight | 3.7 kg |
| Color | White/Red |
| Battery | 1.3Ah 12V |
| Fault contact rating | 30VDC 1 Amp |
| Fire contact rating | 30VDC 1 Amp |
| NO/NC output rating | 0.5A per output (max 1.6A over all outputs) |
| Standby current | 0.065Amp |
| Alarm current | 0.1Amp |
| Operating humidity | 95% (non condensing) |
| Operating temperature | -5°C to +65°C |
Introduction video
Dry-contact devices such as pull stations and water flow switches connect to the WCP-1 through the Contact monitoring module.
✅ Need advice on the WCP-1?
Call FireSmart on 0983.016.201 for consultation and a quote.
Frequently asked questions about the Wireless Fire Alarm Control Panel WCP1
What is the Wireless Fire Alarm Control Panel WCP1 used for?
Wireless Fire Alarm Control Panel WCP1 is a component of the FireSmart fire alarm system.
Is the Wireless Fire Alarm Control Panel WCP1 wireless?
Yes. It connects wirelessly via 444.4 MHz radio, so no signal cabling is required — ideal for renovations and heritage buildings.
Which standard does it meet?
It is designed to meet TCVN 7568-14:2025 (based on ISO 7240), the Vietnamese standard for the design and installation of fire alarm systems.
How can I get a quote or technical support?
Contact FireSmart — a Vietnamese manufacturer of fire alarm devices and systems — for consultation and pricing.
Can I monitor the Wireless Fire Alarm Control Panel WCP1 remotely?
Yes. Connect an FCOM transmission device to the panel’s NO/NC output. It sends alarm calls, and the FireSmart app and PC software show alarms and faults across sites.
